Paxar 4 Manuel d'utilisateur

TC9490OH Rev. CB 3/01 ©1995 Monarch Marking Systems, Inc. All rights reserved.Published by the Technical Communications Department.Printed in the

Loading and Removing the Battery––––––––––––––––––––––––––––To load a battery:1. Turn the printer off. (|) indicates on and (O) indicates off. 2. Tu

Connecting the AC Power Supply –––––––––––––––––––––––––––––cBefore you plug or unplug the power supply, turn the printeroff. Only AC power supplies

4. Plug the AC power supply into a grounded electrical outletof the correct voltage.Connecting the Shoulder Strap ––––––––––––––––––––––––––––––––To c

Using the Trigger and LED –––––––––––––––––––––––––––––––––––The trigger and LED are located on the top of the printer asshown.The trigger serves seve

Chapter 2. Loading SuppliesThe printer can print on labels. We recommend you usesynthetic supplies to print serial or high-density bar codes.Opening

2. Pull the supply guide forward and down as shown.3. Tip the printhead assembly up and over the platen rolleras shown.SupplyGuidePrintheadAssemblyPla

4. Slide the latches on the back of the printer toward thecenter.5. Continue to push the printhead assembly toward the rearof the printer until it ope

6. To close the printer, push the printhead assembly towardthe printer, close the supply guide and latch the faceplateinto place.Loading Ribbon ––––––

Reloading a Ribbon Cassette –––––––––––––––––––––––––––––––––To reload your ribbon cassette, remove the ribbon cassettefrom the printer and follow the

4. Remove the used ribbon and take-up reel and discard.Open a package of new ribbon.nDo Not wrinkle or crush the ribbon.5. With the ridged end of the

Each product and program carries a respective written warranty, the onlywarranty on which the customer can rely. Monarch reserves the right to makech

Loading Supplies––––––––––––––––––––––––––––––––––––––––––––We recommend synthetic supplies when printing serial orhigh-density bar codes. Use only p

2. Squeeze the tabs on the supply holders and align thearrows to the width of your supply. The supply holderslock at each width.ArrowWidth ofSupplyTa

3. Insert the roll of labels between the supply holders andpress until the supply holders lock into the label roll. Thelabel roll should unwind as sh

4. Feed the labels over the peel bar and through the loweropening in the supply guide.5. Close the printer and turn the printer on.6. Wait until the L

Loa ding for Non-Peel ModeNon-peel mode feeds the supplies through the printer withoutpeeling them from the backing paper.nBefore loading supplies, ma

3. Insert the roll of supplies between the supply holders andpress until the supply holders lock into the supply roll.The supply roll should unwind as

4. Feed the supplies through the upper opening in the supplyguide.5. Close the printer and turn the printer on.6. Wait until the LED flashes one time

9490 Operator’s Handbook2-14TC9490OH Rev. C 3/97

Chapter 3. PrintingThe host sends online packets containing print jobs to theprinter. This chapter describes how to communicate with thehost and prin

2. Insert the connector into the printer port until theconnector locks into place. You may hear a click as thecable’s latch snaps into place.3. Gentl

Communica tion ValuesIn order for your printer to communicate with your host, youmust make sure the communication values are set to the samevalues. T

Printing in Continuous Mode ––––––––––––––––––––––––––––––––In Continuous mode, the printer prints a strip of labels. TheLED should be solid amber.

Chapter 4. Care and MaintenancecDo Not use sharp objects to clean the printer. This maydamage the printer and void your warranty.This chapter tells y

Clearing Label Jams–––––––––––––––––––––––––––––––––––––––––When you are printing and a jam occurs, the LED flashesamber and green.To clear a label ja

Cleaning –––––––––––––––––––––––––––––––––––––––––––––––––––You may need to clean the printhead, platen roller, pinchrollers, peel bar, and peel blade

3. Moisten a cotton swab with alcohol. Rub it back and forthacross the printhead, platen roller, pinch rollers, peel bar,and peel blade to remove bui

3. Rub an eraser back and forth on the battery contacts onthe battery as well as inside the battery well. Make surethey are clean.4. Reload the batte

9490 Operator’s Handbook4-6TC9490OH Rev. C 3/97

Chapter 5. TroubleshootingThe printer uses a combination of LED lights to display avariety of printer states. See the "Problems and Solutions&qu

The test label displays the following information:✦Model number (Model:)✦Software version (Software:)✦Number of supplies printed (Stock CNT:)✦Communic

Table of ContentsChapter 1. Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Additional Optional Manuals . . . . . . . .

Problems and Solutions––––––––––––––––––––––––––––––––––––––This section helps you correct some problems that may occur.If you cannot fix a problem, p

Problem SolutionPrinter does notfeed.Check battery.Reload supplies.Verify that the ribbon is not out and that alabel is not jammed in the label path.S

Chapter 6. Using the BootThe Monarch® Renegade® 4 printer’s boot protects it if youaccidentally drop it, hit it against something, or jar it in someot

4. With Shoulder Strap Only. For both sides of the printer,put together the knob assembly and screw it into thethreaded insert. Do not over-tighten

Taking the Boot off the Printer ––––––––––––––––––––––––––––––––To take the boot off the printer:1. Industrial Version Only. Remove the cable from th

9490 Operator’s Handbook6-4TC9490OH Rev. C 3/97

Chapter 7. Using the Cable CoverYou use the cable cover with the industrial version of theMonarch® Renegade® 4 printer. The cover holds the cable in

3. Fit the cable into the groove on the inside of the cablecover.4. Insert the cable connector into printer’s serial port andplace the cover against t

Chapter 8. SpecificationsSpecifications ––––––––––––––––––––––––––––––––––––––––––––––Height: 8.7 inches (221 mm)Width: 8.1 inches (206 mm)Depth: 2.8

Supply Sizes –––––––––––––––––––––––––––––––––––––––––––––––The printer lets you print supplies 2.0 (51 mm) inches wideand up to 6.0 inches (152 mm) l

Chapter 4. Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . 4-1Clearing Label Jams . . . . . . . . . . . . . . . . . . . . . . . .

Cable Pin Outs –––––––––––––––––––––––––––––––––––––––––––––The following table describes the cable pin outs for the printerconnection. The printer u

9490 Operator’s Handbook8-4TC9490OH Rev. C 3/97

GlossaryContinuous mode Print mode in which a format and data witha specific quantity are sent to the printerto be printed in one continuous strip.dow

online Direct communication between a computerand the printer.supplies labels used for printing.System AdministratorPerson responsible for creating an

TC9490OH Rev. CB 3/01 ©1995 Monarch Marking Systems, Inc. All rights reserved.Published by the Technical Communications Department.Printed in the

Chapter 1. Getting StartedThis printer is a portable, online-only unit used to print labels.The host must download data to the printer before the prin

Audience–––––––––––––––––––––––––––––––––––––––––––––––––––The Operator’s Handbook is designed for the person printingand applying labels.This chapter

Charge the battery:✦before using it for the first time✦before lengthy printing sessions✦as soon as the LED indicates a "low battery" conditi

To charge the battery:1. Turn the printer off. (|) indicates on and (O) indicates off.2. The battery can be charged on or off the printer. Plug thec